J-Trace Isolator (8.07.10)
J-Trace Isolator
The
J-Trace Isolator can be connected between a J-Trace PRO V2 or later and
any ARM-board that uses the standard 19-pin, 0.05 inch Cortex-M
connector to provide electrical isolation while keeping high speed trace
capabilities.
SWD Isolator (8.07.01)
SWD Electrical Isolator
The J-Link SWD Isolator can be connected between the J-Link/Flasher and any ARM-board that uses the standard 20-pin JTAG connector to provide electrical isolation. This is essential when the development tools are not connected to the same ground as the application.
JTAG Isolator (8.07.00)
JTAG Electrical Isolator
The J-Link JTAG Isolator can be connected between the J-Link/Flasher and any ARM-board that uses the standard 20-pin JTAG connector to provide electrical isolation. This is essential when the development tools are not connected to the same ground as the application.
J-Link USB Isolator (8.07.02)
USB Electrical Isolator
The J-Link USB Isolator can be connected between the J-Link / Flasher and the host PC to provide electrical isolation.
J-Trace Mictor 38 Adapter
Adapts from 20-pin .05" Cortex trace connector to 38 pin Mictor connector. The pin out follows the single target connector pinout specification as defined in the ARM "ETM Architecture Specification".
J-Link Measurement+Patch Adapter
J-Link Measurement+Patch Adapter
The J-Link Measurement+Patch Adapter provides test points for all
debug signals to allow easy access for test probes, and allows customized wiring between
J-Link and targets that do not provide a standard debug connector.
J-Link 6-pin Needle Adapter (8.06.16)
20-Pin to 6-Pin Needle Adapter
The 20-Pin to 6-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 6-pin, 0.05 inch needle pattern.
J-Link 10-pin Needle Adapter (8.06.04)
20-Pin to 10-Pin Needle Adapter
The 20-Pin to 10-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern.
10-Pin Needle Adapter (8.06.05)
10-Pin to 10-Pin Needle Adapter
The 10-Pin to 10-Pin Needle Adapter converts the 10-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern. Does NOT include 20-Pin to 10-Pin Adapter Board.
SEGGER AVR PDI Adapter (8.06.26)
Adapts from the standard 20 pin 0.1" J-Link connector to the 6-pin 0.1" AVR PDI connector, 6-pin 0.05'' AVR PDI connector or 10-pin 0.1'' AVR PDI connector. Additionally a 5V or 3.3V power supply for the target is integrated.
SEGGER Programming Voltage Adapter (8.06.30)
The SEGGER Programming Voltage Adapter delivers two externally provided voltages to the target for programming targets with voltage requirements beyond 5 V. It can directly be inserted between the Flasher and the debug cable maintaining a 1:1 connection of all debug signals.
SEGGER AVR SPI Adapter (8.06.25)
The
SEGGER AVR SPI Adapter allows to connect a Microchip AVR device with a
SEGGER Flasher device. It support 6 pin and 10 pin Microchip header.
SEGGER Flying Wire Adapter
SEGGER Flying Wire Adapter
Adapts from the standard 20 pin 0.1" J-Link connector to a 10-pin row, allowing to connect J-Link to target PCBs via flying wires.
Especially useful when hooking up prototype HW where no final connector is decided yet. Or for manually connecting a J-Link to ST Discovery boards.
J-Link Target Supply Adapter (8.06.18)
Target Supply Adapter
The J-Link Supply Adapter provides a default voltage of 3.3V to power the target using pin 19. The voltage can be adjusted by replacing resistors.
J-Link Xilinx Adapter
Xilinx Adapter
The J-Link Xilinx Adapter converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 14-pin 2mm pitch connector.
J-Link 2mm Adapter (8.06.11)
2mm Adapter
The J-Link 2mm Adapter converts the 20-pin, 0.1 inch standard connector to a 20-pin, 2mm connector.
SEGGER Intel FPGA Adapter (8.06.15)
SEGGER Intel FPGA Adapter
The
Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the
10-pin 100-mil Intel FPGA JTAG connector providing debug access to FPGA based
MCU cores like the dual-core ARM Cortex-A9 in the Cyclone V devices.
J-Link Supply Adapter (8.06.14)
Supply Adapter
The J-Link Supply Adapter provides a fixed I/O voltage level for VTRef. It eliminates the need to connect VTRef (pin1 on the standard J-Link interface) to the target.
J-Link Signal Smoothing Adapter (8.06.12)
J-Link Signal Smoothing Adapter
The J-Link Signal Smoothing Adapter can be inserted between the J-Link debug probe and the debug target to overcome signal integrity issues.
J-Link TI-CTI-20 Adapter (8.06.06)
J-Link Texas Instruments CTI-20 Adapter
The 20-Pin to 20-Pin CTI Adapter converts the 20-Pin, 0.1 inch standard connector to a 20-Pin TI CTI connection.
J-Link 14-Pin TI Adapter (8.06.03)
14-Pin TI Adapter
The J-Link 14-Pin TI Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch Texas Instruments connector. Includes a 14-pin TI cable.
SEGGER 50-Mil 10-Pin Patch Adapter
SEGGER 50-Mil 10-Pin Patch Adapter
Adapts from the standard 20 pin 0.1" J-Link connector to the standard 10-pin 0.05" Cortex-M connector that is also used on many non-Cortex-M designs but with non-standard pinout. This adapter allows custom connections/wiring between the 20-pin and 10-pin side.
SEGGER STM8 Adapter (8.06.22)
The Flasher STM8 Adapter converts the standard J-Link 20-pin 0.1" connector to the SWIM connector and a standard 10-pin connector.
J-Link Microchip Adapter (8.06.09)
J-Link Microchip Adapter
The J-Link Microchip Adapter converts the standard J-Link 20-pin 0.1 inch target connector to the Microchip RJ11 modular debug connector. Includes 6-pin RJ11 modular connector cable.
J-Link RX FINE Adapter (8.06.10)
RX FINE Adapter
The J-Link RX FINE Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch RX FINE connector. Includes the necessary cable.